气凝胶隔热抗石击涂料 HUALU Pyshield AC-GY-02KSJ01
产品优势
1.轻量化防护盾，卓越抗冲击
2.超强隔热性
3.优异的防火性能
4.超强疏水耐磨
5.施工便捷，无缝包覆
6.超高附着力，不易开裂、剥落
产品参数
|
项目 ltem |
参数 Parameter |
|||
| 抗石击ISO20567-1B法 Stone lmpact Resistance (lSO20567-1B) |
0.5级 Class 0.5 |
|||
|
耐化学性能 Chemical Resistance |
24小时无鼓包，开裂，脱层和过度软化 No blistering, cracking, delamination or excessive softening after 24 hours |
|||
|
附着力 Adhesion |
1级 Class 1 | |||
|
燃烧性能 Flammability Rating |
UL94-2023 V-0 | |||
|
导热系数 Thermal Conductivity |
<0.04 W/(m·k)@25℃ | |||
|
耐磨性能 Wear Resistance |
满足换电耐磨要求 Meets battery swap wear requirements |
|||
|
耐湿热 Damp Heat Resistance |
1级 Class 1 |
|||
|
耐盐雾性 Salt Spray Resistance |
1000小时，锈蚀小于2 mm1000 hours,corrosion <2 mm | |||
|
ROHS6项 ROHS 6 ltems |
不含ROHS 6项有害物质 Free of6 restricted hazardous substances |
|||
|
附加热阻 Additional Thermal Resistance |
约0.2㎡·K/ Approx.0.2 ㎡·K/W | |||
|
耐候性(023 V-0) WeatherResistance(Light Aging) |
400小时无开裂，起泡，附着力无明显下降 WeatherResistance(Light Aging) |
|||
|
规格 Specification |
10 Kg/桶 | |||
|
用量 Usage |
0.6(kg/mm/㎡) | |||
涂层设计结构
|
项目 ltem |
参考厚度(mm) Reference Thickness(mm |
|||
| 基层 Base Surface |
清洁 Clean |
|||
|
防锈底涂 |
<0.2 mm | |||
| 界面剂 Nterface Agent |
20-30 μm 根据表面光泽情况选择使用 20-30 μm (if needed) |
|||
| 气凝胶隔热抗石击涂料 AerogelThermal Insulation and Stone-Chip Resistant Cating |
1.0-2.0 mm | |||
产品应用
气凝胶隔热抗石击涂料具有出色的抗石击、隔热、防冷凝水、降噪性能，适用于动力电池包、汽车底盘、汽车车身、储能柜、储能液冷板、特种车辆、工业管道及储罐的抗石击和保温隔热。
施工要求
|
项目 ltem |
无气喷涂 Airless Spraying |
|||
| 基面要求 Surface Requirements |
对于所有基材都需要进行表面油污清洁处理，要求基材表面张力达36-38 mN/m。 mmAll substrates must be degreased and cleaned, with surface tension reaching 36-38 mN/m. |
|||
|
施工工具 |
喷涂机、辊筒、美纹纸、搅拌器、防护口罩、防护服、安全绳、安全帽、防护鞋、护目镜、保护膜 Spray machine, roller, masking tape, mixer, protective mask, protective clothing, safety rope, safety helmet, safety shoes, goggles protective film |
|||
| 施工工艺 Mixing Instructions |
涂料施工前应该进行充分搅拌以消除物料沉降漂浮带来的不均;搅拌均匀后将物料导入储料罐，进行喷涂一次成型，施工方便快捷 Stir thoroughly before application to ensure uniformity and prevent settling. Transfer mixed material to the feed tank for spraying. |
|||
| 施工条件 Construction Conditions |
1.施工温度不低于5℃，湿度不高于85%。 1.Ambient temperature ≥5°C,humidity s85% |
|||
| 固化条件 Curing Conditions |
80-90℃烘烤固化，1-1.5mm厚度，约60-75分钟烘烤固化:1.6-2mm厚度，约75-90分钟固化。 |
|||
| 涂层检测 Coating Inspection |
涂层厚度控制在1.0-2.0 mm为宜(千膜测厚仪);表面均匀，无裂纹和起泡;使用硬度计测定压痕硬度(邵氏硬度)标准进行硬度测试，测试的硬度值满足:25℃硬度值>75A时可认定为产品已经初步固化，可进行打包运输，对于需要进行极限性能测试(冷热冲击，抗石击，盐雾，冷凝，泡水等)的样板，需在喷涂烘烤后静置7-14天后，同时涂层硬度≥85A(25±2℃，50±5%RH，5s读 数)后再进行测试。 Coating thickness: 1.0-2.0 mm (measured by dry film thickness gauge)- Surace: Uniform, free of cracks and blisters- Hardness test Shore A hardness >75A at 25'c indicates preliminary curing (suitable for packaging and transport. For extreme performance tests (thermal shock, stone impact, salt spray, condensation, water immersion, etc,, samples must stand for 7-14 davs after spraving and baking,with hardness ≥85A (25 ± 2°C, 50 ± 5% RH, 5s reading). |
|||
